Search: Posts Made By: DeClerq
Showing results 1 to 11 of 11
Search took 0.01 seconds.
08-16-14, 12:54 PM
Replies: 2
Views: 1,200
Posted By DeClerq

Ok, thanks. I will try to get it wired up...

Ok, thanks. I will try to get it wired up sometime next week.
08-15-14, 06:36 PM
Replies: 2
Views: 1,200
Posted By DeClerq

Wiring an outlet/switch combo

In my attic there is an electrical box with a light socket/outlet combo. Currently I have a power strip plugged into the outlet and two fluorescent lights plugged into the power strip. To turn on...
05-01-14, 06:53 AM
Replies: 10
Views: 5,021
Posted By DeClerq

All I did was shut off the main water line...

All I did was shut off the main water line entering the house. I did not drain any pipes or the softener (I don't think there was water in it anyway). I think I had a couple of drips of water come...
09-14-13, 02:05 PM
Replies: 6
Views: 986
Posted By DeClerq

I replaced the PB with PEX, went easier than...

I replaced the PB with PEX, went easier than anticipated. I was able to rent a PEX crimper from Menards for $8. Wasn't about to spend $80 buying them.
17766
09-11-13, 05:19 PM
Replies: 6
Views: 986
Posted By DeClerq

What kind of tubing is this and how to replace?

I plan on putting in a larger well pressure tank but am a little stumped at the type of tubing that runs from the tank to rest of the house. The incoming tubing appears to be rubber held on by hose...
08-19-13, 08:44 AM
Replies: 4
Views: 58,394
Posted By DeClerq

Whole house filtration system - before or after softener?

I would like to install a Whirlpool whole house filtration system ( Model #: WHELJ1), but according to their installation diagram, they suggest installing the unit after the water softener for well...
08-19-13, 08:30 AM
Replies: 10
Views: 5,021
Posted By DeClerq

I was able to unscrew it from the copper - a lot...

I was able to unscrew it from the copper - a lot easier than I was anticipating. I could only find a 1" x 1" supply line locally, so only additional piece I needed was at 3/4" to 1" adapter.
16522
08-17-13, 03:51 PM
Replies: 10
Views: 5,021
Posted By DeClerq

Water softener supply lines

I have a leaky water softener supply line that goes from copper to pvc then back to copper. I'm not 100% sure how the pvc is connected to the copper. It appears to be screwed on, but was hopping...
10-27-11, 04:59 PM
Replies: 10
Views: 3,022
Posted By DeClerq

I was finally able to get that bottom fitting...

I was finally able to get that bottom fitting off. I did give it a squirt with WD-40 and let it sit for a few minutes. I put some vice grips on the small length of pipe just above the fitting and...
10-26-11, 04:54 PM
Replies: 10
Views: 3,022
Posted By DeClerq

Thanks for the help. I thought I might have to...

Thanks for the help. I thought I might have to remove that one fitting. I tried briefly to remove it but it's stuck on there pretty good and I don't have a lot of room to get leverage (that blue...
10-26-11, 04:15 PM
Replies: 10
Views: 3,022
Posted By DeClerq

7/8" pipe cap?

So I've got a gas line in my garage that has a branch that ends
with a butterfly or ball valve (to my untrained eye). On other side of the valve was an unused flex line. I removed the flex line...
Showing results 1 to 11 of 11


 
Forum Jump