Search: Posts Made By: John Jennings
Showing results 1 to 19 of 19
Search took 0.01 seconds.
Replies: 4
Views: 367
Posted By John Jennings

Thanks XSleeper, That's the way I'll do it....

Thanks XSleeper,

That's the way I'll do it. :)
Replies: 4
Views: 367
Posted By John Jennings

I am 80% sure I'm going with hard wood on the...

I am 80% sure I'm going with hard wood on the adjacent room but likely not for another year or two. I'm trying to keep it simple because I'm not a good carpenter.

So it sounds like a perpendicular...
Replies: 4
Views: 367
Posted By John Jennings

End Board Perpendicular / Border - Is it Needed?

(FYI the pics are of boards just laid down and not nailed yet)

I'm working with a friend and he said we suggested we put a board perpendicular at the end of flooring. There is another room...
Replies: 4
Views: 1,640
Posted By John Jennings

Alright, I will have to make a piece. Thanks guys

Alright, I will have to make a piece. Thanks guys
Replies: 4
Views: 1,640
Posted By John Jennings

Help with expansion gap stair nose and top of stair landing

I am laying 3/4" hardwood flooring. Part of the floor will start at the top of a stairwell. The floor will span appr. 15'.

I can easily leave a gap along all walls but what do I do for a gap in...
Replies: 4
Views: 227
Posted By John Jennings

I'll run each led strip separately. The 18G...

I'll run each led strip separately.

The 18G is actually less money than the 20G so I'll go with that.

Thanks for the response.
Replies: 4
Views: 227
Posted By John Jennings

I need 5-pin. If I run each strip all the...

I need 5-pin.

If I run each strip all the way back to the PS there will be less amperage on each circuit correct?

I ask because I can buy either 22, 20, or 18 gauge. If I'm running each on...
Replies: 4
Views: 227
Posted By John Jennings

24V LED 5050 wiring Layout and Wire Gauge Question

Any thoughts on this electrical layout?

The blue numbers/lines are showing lengths of wiring I'll use.

The LEDS are strips and they are hi density 24v 5050 LED (RGBW) lights which are...
09-07-18, 02:44 PM
Replies: 7
Views: 1,177
Posted By John Jennings

Ok, with only a small amount of work I will use...

Ok, with only a small amount of work I will use the power from overhead kitchen lights to power my over the sink kitchen light. (makes more sense anyway).


The question is the outlet. It is...
09-07-18, 06:21 AM
Replies: 7
Views: 1,177
Posted By John Jennings

lambition I guess I should have been a bit...

lambition

I guess I should have been a bit clearer.

The counter top now has two dedicated 20a circuits.


The multi wire branch circuit/outlet in question is/was under the sink. Previously...
08-26-18, 12:50 PM
Replies: 3
Views: 1,193
Posted By John Jennings

Disregard this post. There's plenty of room...

Disregard this post.

There's plenty of room to mount my electrical box horizontally under the vent pipe.:o:o
08-26-18, 11:25 AM
Replies: 3
Views: 1,193
Posted By John Jennings

I am now finding out I have an issue with the...

I am now finding out I have an issue with the outlet I need to install. The outlet needs to be within 24" of sink.

My vent pipe will be in the way of my required outlet. Is there another solution...
08-26-18, 06:31 AM
Replies: 3
Views: 1,193
Posted By John Jennings

Move Drain/Vent Pipes - Check my Drawing

I need to move my drain sink over a couple of feet.

There are two drain pipes and they share the same vent. I believe the drain on the right was for a dishwasher.

Anyway, it's a not a load...
Replies: 1
Views: 906
Posted By John Jennings

Wiring Range Hood Requirements

I'm roughing in wire for my kitchen. I want to install a wall mount range hood and won't have the small cabinets above the stove.

When roughing in the wiring, can I use the same circuit as my...
Replies: 9
Views: 829
Posted By John Jennings

My father is the type that would have hired...

My father is the type that would have hired someone to do it so hopefully it was done right. I'll see what he says and go from there. If the buyer wants proof I'll look into hiring someone to inspect...
Replies: 9
Views: 829
Posted By John Jennings

Or get paid and NOT do the work......I'm hoping...

Or get paid and NOT do the work......I'm hoping the 57 is in my favor, lol.

Should I be looking to hire a plumber, septic guy, general contractor, etc to inspect if my father is unsure?
Replies: 9
Views: 829
Posted By John Jennings

One other question. The town plumbing inspector...

One other question. The town plumbing inspector said filling the tank was generally the practice back then. Any guesses on the chances this was done assuming the tank was left 50 years ago and...
Replies: 9
Views: 829
Posted By John Jennings

Alright, that gives me some idea of how to...

Alright, that gives me some idea of how to proceed.

There are 5 of us who are splitting the inheritance. Since I'm not getting reimbursed for my efforts or time I'm thinking paying someone is the...
Replies: 9
Views: 829
Posted By John Jennings

How to Determine if Abandoned Septic Tank Filled

My father's house was converted from septic to town sewage over 50 years ago. The house is for sale and the prospective buyers want to know if the tank was filled. Seeing as how he connected to town...
Showing results 1 to 19 of 19


 
Forum Jump