Search: Posts Made By: Savage
Showing results 1 to 25 of 54
Search took 0.01 seconds.
Replies: 17
Views: 2,219
Posted By Savage

Talking Got it I think

Ok I've been trying to get this to go every which way and finally I think I might have gotten it.

I changed the USP dialer to N.O./momentary and have the yellow going to terminal #9 (Output 1) and...
Replies: 17
Views: 2,219
Posted By Savage

Interesting

Just to test (w/o changing the panel config/programming), I've tried just putting in my 2 wire speaker to output 1 (between Term 4 & 9) and I see 0 vdc in normal run mode. But when I replace those 2...
Replies: 17
Views: 2,219
Posted By Savage

Thanks for you continued help and patience,...

Thanks for you continued help and patience, MrRonFL.

Wouldn't the same also be true- if I test DC voltage between terminal 4 and terminal 9 when not in alarm it should be 0? The AVD-45B in N.C....
Replies: 17
Views: 2,219
Posted By Savage

Unhappy Still not working and I'm not sure why

I've been with the USP tech support and have tested to make sure the dialer (http://www.unitedsecurity.com/avd-45b_manual.PDF) works ok. Here is their simple test:

disconnect white and yellow...
Replies: 17
Views: 2,219
Posted By Savage

Got the dialer connected

I've gotten the USP dialer connected and when I run the test from the USP dialer it dials my cell and give me my recorded message w/o issue. But when I try testing it in "operate" mode with the panel...
Replies: 17
Views: 2,219
Posted By Savage

Almost done.

Thanks MrRonFL.

So the red/green goes across the tip2/ring2 terminals, as well as the grey/brown which are already on the tip2/ring2 terminals, correct?

The yellow/white pair still need the...
04-18-05, 08:18 PM
Replies: 4
Views: 20,928
Posted By Savage

Question Thanks for the help Desy2820. I was...

Thanks for the help Desy2820.

I was wondering if anyone has tested or used a phase coupler?
Replies: 17
Views: 2,219
Posted By Savage

Question Should I open a new thread, even though this is...

Should I open a new thread, even though this is still a continuation of my previous one?
Replies: 10
Views: 1,519
Posted By Savage

Thumbs up Thanks

Thanks for your help MrRonFL.
04-16-05, 07:41 AM
Replies: 4
Views: 20,928
Posted By Savage

Phase coupler for X10 install

I've just started testing a new X10 install and the only issue is some of the outlets are on the wrong "side" of the breaker panel. I was looking into a phase coupler possibly, unless there are other...
Replies: 10
Views: 1,519
Posted By Savage

Got it!

It's working now because of the transformer as you'd imagine. Now the only issue is some of the outlets are on the wrong "side" of you breaker panel. You mentioned looking into a phase coupler...
Replies: 10
Views: 1,519
Posted By Savage

Interesting

MrRonFL, there are instructions on the first few pages with grounding the panel which I'll do and probably try the plain non-grounded transformer for X10.

I currently have digital cable/phone...
Replies: 10
Views: 1,519
Posted By Savage

Transformers, more then meets the eye

After looking into the next version of transformer that is offered for the Power Line Carrier (X10) Card (60-755), I found that it also is w/o the grounding prong and terminal. The customer support...
Replies: 10
Views: 1,519
Posted By Savage

Transformer

Do I swap out the other (Elk) transformer that came with the panel, that I'm currently using? I ordered it as it was a requirement but I thought it was extra. I imagine this is the issue. I figured...
Replies: 10
Views: 1,519
Posted By Savage

Lightbulb Question about GE\ITI Concord and installing wireless lamp module

The instructions aren't too descriptive for either the GE or the X10 with setting up the wireless stuff. I have the module plugged into the panel that allows for the wireless modules. I've got the...
Replies: 1
Views: 1,026
Posted By Savage

I just got my GE Concord and you'll find on this...

I just got my GE Concord and you'll find on this site you can't advertise or you'll be banned. So people will suggest you just do a Google search for the particular thing, i.e. "GE concord security"....
Replies: 17
Views: 2,219
Posted By Savage

Update

I got the voice module setup and it is working well. Thanks!

I'm now installing the USP auto-dialer and wanted to make sure with what you said before. Per instructions...
Replies: 17
Views: 2,219
Posted By Savage

Sorry I'm just a bit confused. I thought...

Sorry I'm just a bit confused.

I thought that the auto dialer (we'll call A) dialed out in emergency and the voice dialer (we'll call B) just provided local/remote phone control of the panel...
Replies: 2
Views: 919
Posted By Savage

Thanks

Good to hear. I just didn't want to cause any problems and I wasn't sure.

Thanks again MrRonFL! :)
Replies: 17
Views: 2,219
Posted By Savage

Question Phone modules

If I have a USP AVD45B Voice Dialer (Auto Dialer) and a GE/ITI Concord Phone Interface and Voice Module (60-777-01), which connects to the system first? I was told they can work together, but do they...
Replies: 2
Views: 919
Posted By Savage

Question Emergency number

I wanted to know if my GE\ITI Concord security system is preprogrammed with the emergency phone numbers or do I have to set them up? I just wanted to know just in case, while I'm testing my...
Replies: 4
Views: 1,311
Posted By Savage

Thanks for the info MrRonFL. With the popularity...

Thanks for the info MrRonFL. With the popularity of cell phone technology I figured they'd have more options...

I'll also look into hardware accessories for cell phones.
Replies: 4
Views: 1,311
Posted By Savage

So do they have programmable Cellular Backup...

So do they have programmable Cellular Backup Transceiver/devices? Or do they only work with the paid service companies? If I can just plug in my emergency #'s into one of those and forget about a...
Replies: 4
Views: 1,311
Posted By Savage

Lightbulb Cell phone connection to security panel

I'm curious to know if there is a way to connect an old working cell phone (with service) to my security panel, if I do have a phone interface and voice module. I know that it connects via RJ-31X...
Replies: 11
Views: 11,595
Posted By Savage

Thumbs up Good news

First, I took the (labeled) wires out of all the zones. Then I just connected the slider sensor to zone 5 with the resistor, it worked. Then I did the same thing but w/o the resistor and of course it...
Showing results 1 to 25 of 54
 


 
Forum Jump