Search: Posts Made By: cc2001
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Replies: 4
Views: 748
Posted By cc2001

have not checked charge rate, but had battery...

have not checked charge rate, but had battery checked under load at reputable battery shop, checked good, also i jumped the solenoid once and cranked perfect
Replies: 4
Views: 748
Posted By cc2001

click when turning key, replaced solenoid, intermittent problem, craftsman 42"

hi
i have a craftsman 42" cut mower, the mower quit starting and would only click at solenoid, i replaced the solenoid and now the mower turns now and then and the other time i get the same click,...
Replies: 6
Views: 917
Posted By cc2001

re

cheese

thanks so much, that was the problem, had oil in the cylinder, this is the same mower that i was working on the brakes on, and i can not for the life of me get them to work right, is there...
Replies: 6
Views: 917
Posted By cc2001

re

thanks geo, these flywheels require a puller to come off correct?

thanks
Replies: 6
Views: 917
Posted By cc2001

ran over steel wire now craftsman acts like valves are out of adjustment, briggs

hi everyone,
i just ran over a piece of steel stiff wire, about a 2ft piece, my craftsman lt1000 has a 16.5 briggs, now it acts just like the valves are out of adjustment, turns over about half a...
Replies: 13
Views: 5,531
Posted By cc2001

thanks cheese i figured that was what to do, i...

thanks cheese
i figured that was what to do, i took them out, got all the rust off with sandpaper lightly sprayed with lubricant, reassembled, brakes are a tiny bit better, stops pretty good at 6th...
Replies: 13
Views: 5,531
Posted By cc2001

thanks cheese, i have taken it apart, one pin...

thanks cheese, i have taken it apart, one pin seems to be more free than the other, how would i know when they are in proper working order? when they both move back and forth freely? Do they need to...
Replies: 13
Views: 5,531
Posted By cc2001

re

ok i see
what i meant was, it will shift on the fly now, but it will not stop, it keeps rolling slowly with pedal down, and when i adjust the brake where it will stop, it will not shift with pedal...
Replies: 13
Views: 5,531
Posted By cc2001

re

so youre not supposed to be able to shift when stopped and clutch pedal/brake pressed? im confused

thanks for your help
Replies: 13
Views: 5,531
Posted By cc2001

re

i depress the clutch but the mower still rolls, it shifts, but i have only done a very few times as i am scared i will mess up tranny or shifter

thanks
Replies: 13
Views: 5,531
Posted By cc2001

thanks cheese i adjusted the rod to original...

thanks cheese
i adjusted the rod to original position, and adjusted brakes, but when i get the brakes where they will stop, the shifting stops again, i can loosen brake nut and it goes back to...
Replies: 13
Views: 5,531
Posted By cc2001

craftsman mower wont shift gears while running

hello everyone
i have a craftsman 16.5 42" cut, problem is as follows, brakes did not eventually got to where they wouldnt stop the mower, checked pads, seemed to have lots of wear left, adjusted...
Replies: 4
Views: 2,781
Posted By cc2001

it was very flexible, I kept gently squeezing...

it was very flexible, I kept gently squeezing until it went in, grabbed it gently with the needle nose pliers and fed it down into the tank

thanks
Replies: 4
Views: 2,781
Posted By cc2001

weedeater featherlite, problem after changing fuel line

Hello
I have a weedeater featherlite, this one has fuel primer bulb, I recently replaced one of the fuel lines, the one going to the primer bulb part of the carb. It was a little larger than the oem...
Showing results 1 to 14 of 14


 
Forum Jump