Search: Posts Made By: LOCKtec
Showing results 1 to 25 of 200
Search took 0.02 seconds.
Replies: 4
Views: 2,635
Posted By LOCKtec

correct- no more intercom from DSC. the...

correct- no more intercom from DSC.

the PC-5961, 5962 & 5964 are speakers with mics for the audio verification modules. to enable an equipped central station to listen & communicate with a...
Replies: 5
Views: 1,394
Posted By LOCKtec

just had a flight and saw something in the sky...

just had a flight and saw something in the sky mall catalog

it was a large parcel box. check it out- iam sure their website address is the same- skymall
Replies: 8
Views: 1,407
Posted By LOCKtec

enroll the keypads at each keypad.

enroll the keypads at each keypad.
Replies: 8
Views: 1,407
Posted By LOCKtec

is the GB actually mounted? attached to the...

is the GB actually mounted? attached to the back plate?

there is a very small tamper switch in the back that gets depressed while attached to the mounting plate. its possible its not closing...
Replies: 10
Views: 1,618
Posted By LOCKtec

the 4500EZ is a bad choice, as it only reports...

the 4500EZ is a bad choice, as it only reports the signal from the siren.

burg or fire.

it does have 3 inputs that can be sent, but its not going to report a siren tamper or low battery.
...
Replies: 9
Views: 1,063
Posted By LOCKtec

its not radio shack™ is it metal or plastic?

its not radio shack™

is it metal or plastic?
Replies: 3
Views: 1,245
Posted By LOCKtec

if you have a low battery, you will get the...

if you have a low battery, you will get the trouble LED on, indicating low battery
the recessed door transmitter does not have a tamper switch.
you will get a trouble condition when you remove the...
Replies: 10
Views: 5,926
Posted By LOCKtec

FYI- the bell time out is in MINS, not seconds...

FYI- the bell time out is in MINS, not seconds !!
Replies: 3
Views: 1,114
Posted By LOCKtec

you may have missed something- the correct...

you may have missed something-

the correct entry is:

*5 xxxx 99 ( not 9 ) then scroll < > to the code you wanna change, then * , then scroll < > to what you want to change &...
Replies: 22
Views: 4,855
Posted By LOCKtec

yeah. if you dont want it calling at midnight ...

yeah. if you dont want it calling at midnight

is it currently at 9999 or 0000 ???

i think it would still make a noise of some sort on the phone
Replies: 5
Views: 4,674
Posted By LOCKtec

we have used many feet of Belden direct burial 6...

we have used many feet of Belden direct burial 6 pair wire that has a heavy copper shield....

all over 100' runs.... never had any issues. used 2 pairs for the keypads and the others for zones...
Replies: 3
Views: 1,459
Posted By LOCKtec

read ALL of the paper that came with the motion...

read ALL of the paper that came with the motion detector- you will read about transmissions being shut down after so many trips to help with battery drain. so it may go into that shut down period...
Replies: 4
Views: 2,824
Posted By LOCKtec

be carful not to loose the spring or pin that is...

be carful not to loose the spring or pin that is in there. the pin to push in is the little thing at the 10 o'clock position
Replies: 3
Views: 3,442
Posted By LOCKtec

if you open & close a door while in the exit...

if you open & close a door while in the exit delay status, it will think you have exited & then any zones programmed as interior will be active.

try the *9 xxxx arming and see what it says -
...
Replies: 22
Views: 4,855
Posted By LOCKtec

they are only "isolated" for as many trips are...

they are only "isolated" for as many trips are programmed in "swinger shutown" . normally set to 003

i dont have a manual handy for that 1565 series.

look in the communication variables...
Replies: 1
Views: 790
Posted By LOCKtec

thats the times for partition 2

thats the times for partition 2
Replies: 4
Views: 844
Posted By LOCKtec

the only concern i would have with doing this-...

the only concern i would have with doing this- and you didnt mention the details of the system - is that there may be FIRE PROTECTION devices connected...

shutting system down would defeat these...
Replies: 3
Views: 1,600
Posted By LOCKtec

YES. it is 2.2k and there should have been...

YES. it is 2.2k

and there should have been -1- included.

if you wire it as shown, it should work


if your doing it on a zone input. you only use a 5.6k
you also need section 013, option...
Replies: 22
Views: 4,855
Posted By LOCKtec

NOTHING is gonna "come up" if you answer the...

NOTHING is gonna "come up" if you answer the "call" you will get just that - a call.

if you dont answer it- you will get a missed call. and if your number is not sent out as "private" you...
Replies: 2
Views: 992
Posted By LOCKtec

is it a YELLOW bypass/trouble LED? or are you...

is it a YELLOW bypass/trouble LED? or are you talking the RED zone status LED ?

try *2 and see if there are any trouble conditions
Replies: 12
Views: 3,756
Posted By LOCKtec

ALL partitions must be DIS-ARMED to do a system...

ALL partitions must be DIS-ARMED to do a system program ( *8 xxxx )
Replies: 13
Views: 1,388
Posted By LOCKtec

since it seems your missing the point - explain...

since it seems your missing the point - explain to who ever takes your order- that you want to use the current window transmitters- and you want to make sure that what they sell you will recieve...
Replies: 13
Views: 1,388
Posted By LOCKtec

you still need to know how the wireless signals...

you still need to know how the wireless signals are recieved at the panel.

either a PC5132 or one keypad with it built in.

if its the keypad- the model number will start RF xxxx
Replies: 13
Views: 1,388
Posted By LOCKtec

each unit has a serial number, these would need...

each unit has a serial number, these would need to be re-programmed for each zone on the new system

- do you know if you have a keypad with a built in reciever? or an external one? box with...
Replies: 13
Views: 1,388
Posted By LOCKtec

you could also use the old keypad- this may be...

you could also use the old keypad- this may be the method of receiving the wireless signals- unless you know if there is a receiver somewhere in the house?

its not all the hard to program, ...
Showing results 1 to 25 of 200
 


 
Forum Jump