Search: Posts Made By: figgsitt
Showing results 1 to 25 of 126
Search took 0.01 seconds.
Replies: 4
Views: 599
Posted By figgsitt

Not sure if my reply was posted, but appreciate...

Not sure if my reply was posted, but appreciate your answer to my question, PJmax. Didn't look close enough at behind the lens ratchet.....thanx.
Replies: 4
Views: 599
Posted By figgsitt

Aha…..Thank you. Hadn't looked closely at...

Aha…..Thank you. Hadn't looked closely at threading area behind the lens. Really appreciate your help.
Replies: 4
Views: 599
Posted By figgsitt

16mm Film Projector

Have some old 16mm films, and a chance to buy a 16mm projector, but it's a sound projector. Can regular "silent" 16mm films be shown on this projector. Everything looks the same.
Thanx.
12-24-18, 05:15 AM
Replies: 2
Views: 295
Posted By figgsitt

Thanx pjmax….will check it out.

Thanx pjmax….will check it out.
12-23-18, 02:16 PM
Replies: 2
Views: 295
Posted By figgsitt

Lights much dimmer than normal.

Had an odd ball occurrence last night. Lights on one circuit started flickering, then entire house went black. Went to main breaker...another building...breaker to house was tripped. Set it, back in...
Replies: 2
Views: 455
Posted By figgsitt

Metal roof installation

Have an addition...6'X18'....slope of 2"/12"....added to an older mobile home. Rolled roofing on now. Would like to cover with metal...BUT...the addition was added flush with the metal roof of the...
Replies: 1
Views: 351
Posted By figgsitt

Roof leak disaster

Had a leak in a roof while I wasn't residing there...5 years. Upon returning I saw that part of the ceiling had sagged considerably...this huge bulge hanging down....which eventually ended up on the...
Replies: 7
Views: 444
Posted By figgsitt

Thanx all, for the suggestions. Charlie

Thanx all, for the suggestions.
Charlie
Replies: 7
Views: 444
Posted By figgsitt

I was afraid of that.....well, with all the good...

I was afraid of that.....well, with all the good epoxies, and adhesives on the market today, I'll attempt something. Thank you for the reply.
Replies: 7
Views: 444
Posted By figgsitt

Yes...I noticed the zerk fittings. Thanx very...

Yes...I noticed the zerk fittings. Thanx very much for the reply.
Replies: 7
Views: 444
Posted By figgsitt

John Deere LT133

I have one of those John Deere LT 133 ....built like a tank....lawn tractor. Steering this thing is like trying to steer a 1958 Impala, with the power steering disconnected....UGH. Also, the hood...
Replies: 11
Views: 908
Posted By figgsitt

Thanks for all the great replies, folks. The last...

Thanks for all the great replies, folks. The last time I was in the crawl space I had thought that the pitch of the sewer pipe from the toilet wasn't steep enough.....and maybe a large Ca Ca would...
Replies: 11
Views: 908
Posted By figgsitt

The vents were my first thought...nest, leaves,...

The vents were my first thought...nest, leaves, etc.....b/c I occasionally get a bubble or two from the toilet, when I drain the bath tub....but the vents are clear. the bowl drains in about 3 to 5...
Replies: 11
Views: 908
Posted By figgsitt

Thanx all for the replies. I've tried very...

Thanx all for the replies. I've tried very lightly pressing the flush handle, not flushing, just enough to fill the bowl to the usual water height. In time, the water level slowly falls to the point...
Replies: 11
Views: 908
Posted By figgsitt

Toilet Draining

Having a problem with my toilet bowl not able to hold water. It's a good quality toilet, not very old. Can see no leaks or cracks anywhere around the toilet. If I keep filling it by pouring H2O into...
11-11-17, 07:26 AM
Replies: 4
Views: 570
Posted By figgsitt

Thank you all for the info....Charlie.

Thank you all for the info....Charlie.
11-10-17, 09:30 AM
Replies: 4
Views: 570
Posted By figgsitt

Mobile home furnace

Is there any way to upgrade a mobile home furnace, 1976 model, short of replacing the entire unit...? I'd like to get a higher heat output. Have tried adjusting the air intake flue, but still...
Replies: 1
Views: 298
Posted By figgsitt

GE front load washer

Have a 2006/7 GE front load Hydro Heater Washer. Has an intermittent squeal at low tub speeds...a louder clunk at higher speeds, in time with tub revolutions. Sounds like a bracket has holding the...
Replies: 3
Views: 638
Posted By figgsitt

Hinge side of door safety

Any ideas, or is there a device to protect little fingers from getting into the hinge side of a heavy door. Been thinking of a strip of rubber, or hard foam to block that opening. Took the door...
Replies: 6
Views: 598
Posted By figgsitt

Thanx for the reply chandler. The sealer seems to...

Thanx for the reply chandler. The sealer seems to dry pretty quickly on the driveway....the hotter, the quicker......???? Anyway, I guess there's no getting around the job I must do.....correctly.
Replies: 6
Views: 598
Posted By figgsitt

It's a bumpout on a larger building,...

It's a bumpout on a larger building, approximately 10 ft X 20 ft. Has already 2 layers of asphalt, 3-tab, WELL WORN shingles. I've been recently thrust into the job of caregiver, so cannot get to...
Replies: 6
Views: 598
Posted By figgsitt

Sealing leaky roof

Has anyone ever used that black driveway coating to coat a roof with small leaks.....until a permanent roof can be installed...?
Replies: 9
Views: 991
Posted By figgsitt

Thanx guys for all the info....appreciated. ...

Thanx guys for all the info....appreciated.
Charlie
Replies: 9
Views: 991
Posted By figgsitt

Tire sizes

How much leeway is there in the tire sizes on the non-drive wheels...? If 215 70 15 is listed, could a 225 70 15, 0r 205 70 15 be put on the rear wheels of a front wheel drive car...if it's just a...
Replies: 8
Views: 622
Posted By figgsitt

I do have an account. I've been into the manage...

I do have an account. I've been into the manage accounts window, but cannot find where to change the settings....
Thanx for all the info, folks.
Showing results 1 to 25 of 126
 


 
Forum Jump