Search: Posts Made By: Ron53
Showing results 1 to 25 of 200
Search took 0.02 seconds.
Replies: 6
Views: 256
Posted By Ron53

My initial thought is to flush and replace the...

My initial thought is to flush and replace the fluid in the system, could be fluid is just worn out and have excessive moisture in it.
Replies: 7
Views: 173
Posted By Ron53

Now is not the time to buy a printer with the...

Now is not the time to buy a printer with the prices getting as bad as lumber. You might try taking a old towel and laying one layer of it across the print nozzles then take a vacuum hose and put it...
09-27-20, 12:38 PM
Replies: 6
Views: 458
Posted By Ron53

Maybe you could try tightening the bolt, it may...

Maybe you could try tightening the bolt, it may have just loosened from use.
09-27-20, 11:30 AM
Replies: 11
Views: 335
Posted By Ron53

Compound bows have the string length and the...

Compound bows have the string length and the cable length on the information sticker on the bow. I have always used Zebra strings and cables on my bows, they are a little pricey but are very good...
09-25-20, 08:26 AM
Replies: 5
Views: 257
Posted By Ron53

Maybe someone can enlighten me as to how that...

Maybe someone can enlighten me as to how that floor can be detrimental to using it for an artist studio/workshop in it's present condition. It seems like a lot of work to make it level for such a...
Replies: 6
Views: 249
Posted By Ron53

The only thing it would be useful for is a...

The only thing it would be useful for is a planter in your front yard. Send it back.
Replies: 13
Views: 882
Posted By Ron53

You might consider replacing the seal with one...

You might consider replacing the seal with one that isn't deformed and if you have a door opener you might also adjust the downward travel a little more.
Replies: 6
Views: 224
Posted By Ron53

If those were the first boards he installed on my...

If those were the first boards he installed on my deck I would fire him on the spot. I think his poor work and attitude will continue and the rest of the install has the strong possibility up being...
08-13-20, 04:26 AM
Replies: 4
Views: 212
Posted By Ron53

I bought a couple of rolls off Ebay a long time...

I bought a couple of rolls off Ebay a long time ago and they have worked fine, still have some since I don't use them much. One note, if your going to seal meat put it in the freezer and partially...
Replies: 2
Views: 102
Posted By Ron53

Just mark the old screw locations in the new...

Just mark the old screw locations in the new plate, drill holes in plate to match up with old screw locations and it will be fine.
Replies: 22
Views: 608
Posted By Ron53

Well you don't want anything that says "daylight"...

Well you don't want anything that says "daylight" even in LED bulbs. But the soft white LED bulbs do hold up well from on and off cycles I don't know where you got that idea. If nothing works out for...
Replies: 31
Views: 818
Posted By Ron53

Your other and maybe the best overall option...

Your other and maybe the best overall option would be to convince the wife that it isn't repairable and you need to buy another boat.
Replies: 13
Views: 371
Posted By Ron53

You might look for some You Tube videos on the...

You might look for some You Tube videos on the subject. It will either scare you into paying to have it done or put your mind at ease at doing them yourself. I have a F-150 with the 5.4 engine and...
Replies: 31
Views: 818
Posted By Ron53

I still think you are going to have structure...

I still think you are going to have structure problems if you go cutting that glass, especially if you don't have much or any experience in laying glass maybe you could find someone to help with it....
Replies: 31
Views: 818
Posted By Ron53

Understand the weight concern but that is shear...

Understand the weight concern but that is shear weight and gluing it won't change that either way, just strategic placement of the through bolts should be sufficient. I would be most concerned with...
Replies: 31
Views: 818
Posted By Ron53

I really don't think you are going to compromise...

I really don't think you are going to compromise the transom with a few holes or bolts with fender washers since they will in effect make it a single unit. And if it fits that tight I again would not...
Replies: 17
Views: 296
Posted By Ron53

Or you could just go to Lowes or Home Depot and...

Or you could just go to Lowes or Home Depot and get a bottle of oil marked, Air Compressor Oil, so there won't be any question that you have the correct oil.
Replies: 31
Views: 818
Posted By Ron53

You know after reading this I got to wondering if...

You know after reading this I got to wondering if the fiberglass was ever attached to the wood or how long the boat was used without knowing one way or the other. I'm thinking to myself that I...
Replies: 2
Views: 150
Posted By Ron53

The only thing I can offer is look for some...

The only thing I can offer is look for some YouTube videos on rewinding the spring, you should be able to find one that will help. Some of those guys are pretty creative when it comes to doing the...
Replies: 21
Views: 482
Posted By Ron53

So, in total you paid 575.00, is that what what...

So, in total you paid 575.00, is that what what your saying? If so you definitely need to find a new plumbing business. You could have bought a good powered snake for that and had it available for...
Replies: 8
Views: 247
Posted By Ron53

You could also try uninstalling any recent...

You could also try uninstalling any recent updates.
Replies: 1
Views: 177
Posted By Ron53

In theory, yes. But you would need to use the...

In theory, yes. But you would need to use the same diameter pulley, the correct voltage regulator and find the proper belt to fit on all the pulleys . Just get the proper replacement for your...
Replies: 6
Views: 280
Posted By Ron53

The blue wire on a 5 way connector is an...

The blue wire on a 5 way connector is an auxiliary wire that is often used for backup lights.
06-27-20, 02:07 PM
Replies: 4
Views: 310
Posted By Ron53

You should also put a couple of lag bolts through...

You should also put a couple of lag bolts through the back wall of the safe into the house wall for more security and to prevent any tipping possibility.
Showing results 1 to 25 of 200
 


 
Forum Jump