Search: Posts Made By: mongo1969
Showing results 1 to 25 of 39
Search took 0.01 seconds.
Replies: 5
Views: 927
Posted By mongo1969

Sorry, I take that back...It is loose when...

Sorry, I take that back...It is loose when engaged..
Replies: 5
Views: 927
Posted By mongo1969

It's not as loose, but not as tight as it should...

It's not as loose, but not as tight as it should be....
Replies: 5
Views: 927
Posted By mongo1969

Craftsman 536.720720 riding mower

I have a riding mower that the blades do not seem to be rotating properly. I checked the belt and it seemed loose, so I ordered a new one. Stock part number is 37X111. I got the belt and installed...
Replies: 1
Views: 1,254
Posted By mongo1969

Craftsman 6.0hp OVC, no spark

I have taken the magneto off and cleaned the contacts and made sure the flywheel is free of rust and debris. It was working fine 2 days ago,and now no spark!! This is a Craftsman power washer, by...
Replies: 2
Views: 3,426
Posted By mongo1969

Thanks Glen. I ended up retrofitting another...

Thanks Glen. I ended up retrofitting another Walbro carb to the weed eater and it runs like a champ....thanks for the quick help, I will start trying that now.
Replies: 2
Views: 3,426
Posted By mongo1969

Walbro WT682

I just bought the rebuild kit for this Walbro and it fires and runs for about 2 seconds and dies. As I was cranking on it again I've found gas spitting out of the muffler. It was doing this before...
Replies: 1
Views: 1,349
Posted By mongo1969

Sears 5.5 HP self propelled mower

I have a Sears 5.5 self propelled mower with a Techumseh engine on it. I don't have the model number because Sears only put their stock number on it. It is 143.945504. I have deduced that this is...
Replies: 4
Views: 13,680
Posted By mongo1969

thanks everyone...I will get a new kit and try...

thanks everyone...I will get a new kit and try everything suggested!! Thanks again.
Replies: 4
Views: 13,680
Posted By mongo1969

Homelite 33cc chainsaw with Walboro Carb

Airman is a genius when it comes to Walboro carbs!! Any submissions are welcome. I have a 33cc Homelite chainsaw and have a problem when giving it gas. I have cleaned the carb and blew it out with...
Replies: 1
Views: 1,769
Posted By mongo1969

MTD model # 13RL771H029 20hp and 46in tri cut

I have the above mentioned rider and don't have the belt direction of the drive pulley for the belt. I have looked online and can't find a manual or anything for the direction of the belt. Can...
Replies: 5
Views: 3,008
Posted By mongo1969

Thanks everyone for your input. I sprayed this...

Thanks everyone for your input. I sprayed this stuff called PB Max from Home Depot on the shaft and inside the key way. I let it sit for a couple of days and slid right off. The bottom part of the...
Replies: 5
Views: 3,008
Posted By mongo1969

I will try the penetrating oil and see if that...

I will try the penetrating oil and see if that works to loosen it. I know it's not the valves because I can hand turn the engine three or four times and it stops like something is blocking it. I...
Replies: 5
Views: 3,008
Posted By mongo1969

Yard Machine 38" cut with 12.5 hp Briggs

I have a Yard Machine riding lawnmower that I have to pull the engine and look to see why there is no compression. It is the either the piston arm or wrist pin or something. Won't be able to tell...
Replies: 2
Views: 2,845
Posted By mongo1969

Stihl BG 65 leaf blower

I have a Stihl BG 65 leafblower and the muffler gets red hot and glows after about 5 or ten minutes after started. Is this caused by a bad muffler or is it something else?? It's a two stroke. ...
Replies: 1
Views: 1,063
Posted By mongo1969

LT4000 Craftsman

I have a Craftsman LT-4000 with 42" deck 13 HP Kohler. It starts up, but the blades will not engage. Do you think it could be a safety sensor that has gone bad??? Thanks in advance!!

Mike
Replies: 3
Views: 3,968
Posted By mongo1969

Thanks M. for the quick response. I think I...

Thanks M. for the quick response. I think I figured out my problem. It is the float needle. Techumseh put two different diaphragm carbs on this model. Depending on which one you have depends on...
Replies: 3
Views: 3,968
Posted By mongo1969

It's not the float bowl type, it the diaphram...

It's not the float bowl type, it the diaphram type. So maybe that is sticking.
Replies: 3
Views: 3,968
Posted By mongo1969

Simplicity Snowbuster 220

I have a Simplicity Snowblower that is about 20 years old. There have never been any problems with it in the past. This year I could only get it to run on choke. So I bought a carb kit for it and...
Replies: 5
Views: 1,155
Posted By mongo1969

For what it's worth, I had the same problem with...

For what it's worth, I had the same problem with an MTD riding mower and it was what Cheese had said, it was a stuck throttle shaft in the carb.
Replies: 3
Views: 1,034
Posted By mongo1969

Thanks 30year for the speedy response!! I just...

Thanks 30year for the speedy response!! I just noticed that there is a small amount of gas that spatters up from the intake as well. Before I start tearing apart the linkages and reinstalling...
Replies: 3
Views: 1,034
Posted By mongo1969

MTD Lawn tractor

I have a MTD lawn tractor with Briggs and Stratton 422707-1214-01. I rebuilt the carb on this thing and it wants to run at full speed. I've backed the idle screw out almost all of the way and still...
Replies: 7
Views: 2,965
Posted By mongo1969

Thanks for the responses. I replaces the Mobile...

Thanks for the responses. I replaces the Mobile 1 with SAE30 and the smoke has decreased tremendously. When I run at half throttle it hardly smokes and no oil out of the exhaust. When I run at...
Replies: 7
Views: 2,965
Posted By mongo1969

Come to think of it...before I tear it apart, I...

Come to think of it...before I tear it apart, I put Mobile 1 synthetic oil in it. That could be too thin and why it's blowing oil out of the exhaust.....I should drain and put SAE30??
Replies: 2
Views: 1,381
Posted By mongo1969

I would definitely get a Torx bit (star shaped)...

I would definitely get a Torx bit (star shaped) set and take off the carb and give it a thorough cleaning. If you have an air compressor, blow out the jets. Also, check the carb bowl nut and make...
Replies: 7
Views: 2,965
Posted By mongo1969

I've never seen this engine either. I found that...

I've never seen this engine either. I found that it is a 49cc engine. I will tear it apart today and update. Thanks for the fast response.
Showing results 1 to 25 of 39
 


 
Forum Jump