Search: Posts Made By: scottg
Showing results 1 to 25 of 200
Search took 0.02 seconds.
03-12-06, 08:57 AM
Replies: 7
Views: 21,041
Posted By scottg

Voltage

You need to check the circuit for power Reset breakers or replace fuses and try again.
03-12-06, 08:08 AM
Replies: 5
Views: 2,007
Posted By scottg

repairs

It sounds like the bi-metal thermostat is stuck in the closed position. With power disconnected. The front cover of the furnace should just lift up then off away from the wall. Then you will see 2...
03-12-06, 08:00 AM
Replies: 5
Views: 1,450
Posted By scottg

Troubleshooting

It sounds like to me that it is another one fo the problems that Carrier has with their furnaces it appears as though the contractor that installed the furnace left it in your house. Carrier puts out...
03-12-06, 07:48 AM
Replies: 5
Views: 1,165
Posted By scottg

Here's the stuff

m/n GUN100-4

using lp

13.2 inlet psig.

10.2 man. psig.

flame looks like
03-07-06, 08:07 PM
Replies: 5
Views: 1,165
Posted By scottg

They are ribbon burners on a janitrol furnace 94...

They are ribbon burners on a janitrol furnace 94 yr model
03-07-06, 07:06 PM
Replies: 5
Views: 1,165
Posted By scottg

gas adjustment link

Does anyone have any info on gas burner adjustment ?

I changed out a set of burners on a furnace because of rust and now I get some flames inside of the burner. I would like to get some reasons as...
02-19-06, 12:01 PM
Replies: 6
Views: 2,931
Posted By scottg

Possible problems may still exhist

Hey did the repair company do a moisture test of the refrigerant circuit? This may be the cause of the compressor failure. If the is moisture in the circuit the new compressor will not last too long.
07-09-05, 03:25 PM
Replies: 3
Views: 2,042
Posted By scottg

Can you pump it down and capture the refrigerant...

Can you pump it down and capture the refrigerant in the unit. This will tell if the compressor is laboring or doing it's job.

What happens with shutting down the vapor valve when in the cool mode...
07-09-05, 03:14 PM
Replies: 2
Views: 917
Posted By scottg

Yes most pressure switches are screwed on the...

Yes most pressure switches are screwed on the system with a 1/4'' fitting that has a valve core.
What I have found is if I cut the wires as short as possible then it is easier to remove quickly,...
07-01-05, 06:57 PM
Replies: 2
Views: 1,180
Posted By scottg

Carrier has a 5 min. time delay built into the...

Carrier has a 5 min. time delay built into the outdoor control. It will not pull in the contactor when power is interrupted for 5 min.
You can speed this up by momentarily jumping across the speed...
07-01-05, 06:41 PM
Replies: 13
Views: 1,909
Posted By scottg

Well according to york a flashing code of 2 is...

Well according to york a flashing code of 2 is discharge pressure is over 400 psig.

This can happen from many different senerios. I hope that I spelled that right.
But anyways you could be over...
06-26-05, 11:59 PM
Replies: 10
Views: 1,587
Posted By scottg

This could be a number of things I would first...

This could be a number of things I would first call your power compny first. It maybe your connection between the meter and the house
06-26-05, 11:45 PM
Replies: 14
Views: 15,738
Posted By scottg

First check to see if both units are blowing air...

First check to see if both units are blowing air inside the house and outside the house.
Second check the temperature of the connecting copper lines at the outsid unit the big one should be cold and...
06-26-05, 11:36 PM
Replies: 3
Views: 2,663
Posted By scottg

the Rheem units are great at removing the...

the Rheem units are great at removing the moisture in the air and are a good at cooling. The modle that you stated is a ten seer heat pump out door unit, My question is what do you have for an indoor...
06-26-05, 10:42 AM
Replies: 2
Views: 2,319
Posted By scottg

Honeywell has a commucating interface that can...

Honeywell has a commucating interface that can control humidity, cooling and heating. This can all be monitored with a phone call. You can also change the settings by a phone call.
Check it out at ...
06-18-05, 05:50 PM
Replies: 3
Views: 8,015
Posted By scottg

"anti sieze compound"

With what ever way that you go repair or replacement the need to use "anti sieze compound" on all the moving parts ie... the pulley hub, the shaft, the bearing hub, and the squirell cage hub. This...
06-18-05, 05:36 PM
Replies: 5
Views: 19,555
Posted By scottg

"anti sieze compound"

I am a real believer in the use of "anti sieze compound". Apply this on all the moving parts ie pulley, shaft, bearing hubs, squriel cage hub, and set screws. Believe me when it comes time to replace...
06-18-05, 05:28 PM
Replies: 5
Views: 28,722
Posted By scottg

Hey Fricka, You will need to apply some...

Hey Fricka,

You will need to apply some "anti seize compond" on the shaft and other parts so when the next time you can take it apart easier. I would also apply a new coat each year when you do...
06-11-05, 08:17 PM
Replies: 6
Views: 1,157
Posted By scottg

Well are you sure that the thermostat wiring...

Well are you sure that the thermostat wiring doesn't have a short. Thats what it sounds like to me.
06-11-05, 08:02 PM
Replies: 2
Views: 1,099
Posted By scottg

Sounds like the compressor is out on thermal...

Sounds like the compressor is out on thermal overload.
06-11-05, 07:58 PM
Replies: 6
Views: 1,157
Posted By scottg

Well it sounds like it is time to get a pro.

Well it sounds like it is time to get a pro.
06-09-05, 07:12 PM
Replies: 5
Views: 7,388
Posted By scottg

The difference is that the Rheem unit uses the...

The difference is that the Rheem unit uses the Copeland Scroll compressor and the Weather King uses a Bristol recip. compressor.

The scroll being the better compressor.
06-09-05, 06:32 PM
Replies: 2
Views: 1,570
Posted By scottg

Check to see if there is freon in it by...

Check to see if there is freon in it by depressing the valve core with a tire gauge. Itshould have a pressure higher than 50.

It may be out on low pressure switch.
06-09-05, 05:45 PM
Replies: 5
Views: 1,047
Posted By scottg

A good Lennox tech would have a diagnosis tool...

A good Lennox tech would have a diagnosis tool that you connect to the motor and it will tell you if it is the motor the motor controller or the control interface board.

Then get just the part...
06-09-05, 05:33 PM
Replies: 1
Views: 2,904
Posted By scottg

You may have got some one to repair your unit...

You may have got some one to repair your unit already but I think that you really need to have thr fossil fuel control to get this to run properly. I don't really think that I can give you any real...
Showing results 1 to 25 of 200
 


 
Forum Jump