Search: Posts Made By: mehand
Showing results 1 to 22 of 22
Search took 0.01 seconds.
Replies: 5
Views: 2,105
Posted By mehand

Power up - check sequence completes and the...

Power up - check sequence completes and the screen is lighted only - a white screen.
Replies: 5
Views: 2,105
Posted By mehand

Lynx L5000PK blank screen

Just purchased the Lynx Touch Screen L5000PK system. Mounted control panel, applied power and phone line. Goes through start up sequence - system OK then white screen ? Need help !!!
Replies: 1
Views: 818
Posted By mehand

Siren

I have installed 2 Wave speakers in my 20P system . I wired them in parallel - correct? or should be in series?
Replies: 2
Views: 878
Posted By mehand

Awesome

Thank you very much! You were right on. Both keypads are operational and the fobs are working.
Replies: 2
Views: 878
Posted By mehand

Change from Vista 15 to 20

I have recently changed my system from a Vista 15 to a 20. I have run across two issues that I have not yet resolved. Key pad 6160RF is set at add:16 and works fine, the second keypad 6160V is not...
Replies: 5
Views: 2,294
Posted By mehand

If this is the case is the practical choice to...

If this is the case is the practical choice to purchase the more expensive 5883H which has 64 expanded zone capability and just use the 6150Rf keypad as a keypad only?
Replies: 5
Views: 2,294
Posted By mehand

The 6150rf keypad continues to control 16...

The 6150rf keypad continues to control 16 wireless zones and adding the 5881enm 16 zone expander will give me access to the remaining 10 wireless zones?
Replies: 5
Views: 2,294
Posted By mehand

Vista 15P Wireless Expansion

I have a Vista 15p - 6150rf and 6160v keypads with 16 programmed wireless zones. I attempted to add additional zones and I receive an error E8 on the keypad which denotes the wireless receiver...
Replies: 9
Views: 2,556
Posted By mehand

I powered down the system, reset the 6160V. Read...

I powered down the system, reset the 6160V. Read more in programming manual - powered down again, entered program mode *26 + 0. Exited program mode and all is well chiming and annunciating all zones....
Replies: 9
Views: 2,556
Posted By mehand

Chime

None of the zones chime. But the keypad says chime is on or chime off which I have turned on and off many times without success. The 6160V keypad reports which fault is present in alpha format and...
Replies: 9
Views: 2,556
Posted By mehand

Chime

I programmed them Type 01
Replies: 9
Views: 2,556
Posted By mehand

Tried

I entered the master code + 9 ####9. When entering the master and 9 I hear a chime from the keypad for acceptance turning on or off the chime and the ###9 following has no effect.
Replies: 9
Views: 2,556
Posted By mehand

Vista 15p - Chime

Vista 15p - 6160rf & 6160V keypad wireless transmitters - I can not get the chime to work when opening entry doors. Does this feature only work with wired sensors? Or do I need to program the...
Replies: 1
Views: 1,070
Posted By mehand

7845-GSMR - Digital Cellular Communicator

With your help I have successfully installed and setup a Vista 15p, 2 keypads, 17 wireless transmitters (so far) including wired and wireless smokes and IR detectors. All works great and the family...
Replies: 2
Views: 1,050
Posted By mehand

Hard Wired 2 Wire Smoke

I have a Vista 15P basically wireless until this point. I am adding a Meridian MN220 2-Wire Smoke and have connected to terminals #8 & #9 in the panel observing polarity . Programmed to zone 1 & 09...
Replies: 3
Views: 954
Posted By mehand

Awesome, I can continue to add above the 16 units...

Awesome, I can continue to add above the 16 units using the 6150RF keypad? I should have tried I guess.
Replies: 3
Views: 954
Posted By mehand

Vista 15p /6150RF Wireless Expansion

I have installed a Vista 15p with 6160V and 6150RF keypads. After successfully setting up windows, door and fire transmitters I find myself short of 5 more wireless zones and I may add more later....
Replies: 4
Views: 802
Posted By mehand

I should have read other posts before and not...

I should have read other posts before and not after... I needed to purchase the 6160rf!
Replies: 4
Views: 802
Posted By mehand

Thanks! I have ordered a 6160 alpha numeric...

Thanks! I have ordered a 6160 alpha numeric keypad. I have already installed the 15P panel and 6150 Rf keypad which is needed for the wireless components. Can I disconnect the 6150, connect the 6160...
Replies: 2
Views: 1,876
Posted By mehand

Recycling

I manage a materials recovery facility designed to extract and recover materials found within construction and demolition debris collected locally and as far away as Staten Is,NY. The facility is...
Replies: 4
Views: 802
Posted By mehand

Clear Old Codes

I have purchased a Vista 15p system which was taken out of a home prior to demo. How do access and clear the old codes to begin a new setup? (6150RF keypad)
Replies: 1
Views: 837
Posted By mehand

Shopping for Alarm System

I am interested in purchasing and installing my own system. Considering a wireless hybrid system. I also would like options to call personal numbers and possibly a monitoring company.

I have...
Showing results 1 to 22 of 22


 
Forum Jump