Search: Posts Made By: drummernick
Showing results 1 to 19 of 19
Search took 0.01 seconds.
Replies: 25
Views: 44,717
Posted By drummernick

I got mine on EBAY - I am in the UK, so a...

I got mine on EBAY - I am in the UK, so a specific link probably not useful, but let me know if you want me to dig it out?
Replies: 1
Views: 2,506
Posted By drummernick

Leaking shower head

I have a good quality Hansgrohe shower head which is leaking at the joint between the flexible hose and the head itself. The link below gives a diagram of the setup. There seem to be 2 joints near...
Replies: 5
Views: 812
Posted By drummernick

Only with your help! The stat kit arrived...

Only with your help!

The stat kit arrived today, and I replaced both. Dryer is now heating again. Hero status achieved once more ...

Thanks for your help.
Replies: 25
Views: 44,717
Posted By drummernick

marbobj thanks - I tried that, but pumping the...

marbobj thanks - I tried that, but pumping the primer bulb makes the engine run worse rather than better.

Just one thought - the picture right at the beginning of this thread shows 2 springs on...
Replies: 5
Views: 812
Posted By drummernick

Yes I know you guys are mostly in the USA, but I...

Yes I know you guys are mostly in the USA, but I have found everyone so helpful, and you are no exception!

Thanks a lot for the video link - I popped the machine open yesterday and tested those...
Replies: 25
Views: 44,717
Posted By drummernick

Thanks for your latest ideas. Marbobj, I...

Thanks for your latest ideas.

Marbobj, I tried loosening (and removing) the gas tank filler cap while running, but it made no difference. Nice thought though.

Geogrubb, I have had the main jet...
Replies: 5
Views: 812
Posted By drummernick

Tumble Dryer Heater Broken

Hi,

I am in the UK, and have a Creda Reversair tumble dryer (no model number to be found on the front).

All is working OK, except the air is no longer getting heated. I have previously replaced...
Replies: 10
Views: 12,888
Posted By drummernick

Fixed!

Well that worked perfectly. Took about 5 mins to replace the motor, and now it works perfectly.

Thanks a lot for the ideas, and especially the link to the part!
Replies: 25
Views: 44,717
Posted By drummernick

I don't think it's that. I have taken out the...

I don't think it's that. I have taken out the jet, run a paperclip through it to make sure it's clear, checked the 'o' ring and snapped it back into place in the carb. I do think you're on the right...
Replies: 25
Views: 44,717
Posted By drummernick

Hi guys, I did follow all those instructions...

Hi guys,

I did follow all those instructions very carefully. I have been through the procedure a lot over the last few days, so I'm fairly familiar with it all. The diaphragm is definitely on the...
Replies: 25
Views: 44,717
Posted By drummernick

Disappointment. The parts came today and I fitted...

Disappointment. The parts came today and I fitted the new diaphragm and gasket (diaphragm nearest the tank). I also cleaned up the spark plug. However, whilst the engine does now run better at idle...
Replies: 10
Views: 12,888
Posted By drummernick

OK I have ordered the motor - will update when...

OK I have ordered the motor - will update when I've fitted it.
Replies: 10
Views: 12,888
Posted By drummernick

Yes I am - hey thanks that's very kind. From the...

Yes I am - hey thanks that's very kind. From the look of that part, it's relatively sealed, so I would just replace the whole thing?

Would be good to be able to test the old one - is that going to...
Replies: 10
Views: 12,888
Posted By drummernick

Aha I just found a model number in tiny letters...

Aha I just found a model number in tiny letters on the front:

Panasonic NN-T573S
Replies: 10
Views: 12,888
Posted By drummernick

Microwave Oven platter not turning

Hi,

I have a Panasonic worktop microwave oven - standard domestic model (although I can't see a model number anywhere front or back). It has a glass platter inside mounted on top of a plastic...
Replies: 25
Views: 44,717
Posted By drummernick

Well, it seems unanimous that a new diaphragm is...

Well, it seems unanimous that a new diaphragm is the way forward. I will order one up and report back ...!

Thanks so much for your thoughts so far - really appreciate it.

Nick.
Replies: 25
Views: 44,717
Posted By drummernick

Aha - I have pulled the plug a couple of times...

Aha - I have pulled the plug a couple of times and it IS very black and sooty. So I guess 2 questions:

1. Given that, does it take you down a different path? If the mixture is too rich, what can I...
Replies: 25
Views: 44,717
Posted By drummernick

Thanks for the replies! Marbobj I'm not sure...

Thanks for the replies!

Marbobj I'm not sure I follow you. What I'm saying is that there are two situations where the revs do actually pick up nicely:

1. When the gas tank runs out - or just in...
Replies: 25
Views: 44,717
Posted By drummernick

Briggs and Stratton 3.5hp problem

Hi all,

I am hoping from looking at other threads that one of you gurus can help me. I have a simple push along mower with a 3.5 hp B&S engine - the one with the plastic pulsa carb. Someone posted...
Showing results 1 to 19 of 19


 
Forum Jump