Search: Posts Made By: Jeremy S
Showing results 1 to 12 of 12
Search took 0.01 seconds.
11-05-17, 06:54 PM
Replies: 9
Views: 2,139
Posted By Jeremy S

Cool I ended up going with Silverline 3900 new...

I ended up going with Silverline 3900 new construction windows for my project, purchased from a local door/window store. I received a quote for some Anderson 100 series vinyl windows but they felt...
11-01-17, 11:44 AM
Replies: 9
Views: 2,139
Posted By Jeremy S

Does anyone have any experience with Reliabilt...

Does anyone have any experience with Reliabilt 3201 series windows?
11-01-17, 09:17 AM
Replies: 9
Views: 2,139
Posted By Jeremy S

A local supplier has the Silverline 1200 series...

A local supplier has the Silverline 1200 series windows, which are bottom of the barrel from what I have read. I also have in my area Home Depot (American Craftsman), Lowes (Thermastar by Pella), and...
10-30-17, 02:21 PM
Replies: 9
Views: 2,139
Posted By Jeremy S

Replacement Windows

I am going to help a friend replace some of the 40+ year old windows in her home. The original windows were not very high quality to begin with, single pane and flimsy aluminum frames that don't...
08-20-14, 07:31 PM
Replies: 11
Views: 12,292
Posted By Jeremy S

So I finally got this resolved. I had a HVAC...

So I finally got this resolved.

I had a HVAC Technician take a look at it. He verified that the ECM 2.3 module that I had purchased was bad, but could find nothing else wrong in the system.
...
08-12-14, 06:10 AM
Replies: 11
Views: 12,292
Posted By Jeremy S

When I work on it again I will clean the coils...

When I work on it again I will clean the coils out if they need it and check the filter.

I am gun shy of installing another $300+ control module on this motor and having it cook just a few minutes...
08-11-14, 03:32 PM
Replies: 11
Views: 12,292
Posted By Jeremy S

Magnets are still intact and motor spins freely.

Magnets are still intact and motor spins freely.
08-11-14, 07:53 AM
Replies: 11
Views: 12,292
Posted By Jeremy S

This has been a working system since 2006 until...

This has been a working system since 2006 until this motor falied. I have no way of measuring static pressure. What could have changed that would effect static pressure?

Can a fan control module...
08-11-14, 07:02 AM
Replies: 11
Views: 12,292
Posted By Jeremy S

I am going to try to get the control module...

I am going to try to get the control module replaced but before installing another I'd like to verify that it was a factory defect that caused the other to fail versus a problem in the furnace...
08-08-14, 06:40 AM
Replies: 11
Views: 12,292
Posted By Jeremy S

I have read a variety of winding resistance...

I have read a variety of winding resistance values online for this motor. Mine is a 1/2HP model.

What should I expect to measure between and of the 3 pins on the motor portion? I suspect that the...
08-08-14, 06:24 AM
Replies: 11
Views: 12,292
Posted By Jeremy S

The blower spins freely, no resistance at all. I...

The blower spins freely, no resistance at all. I did check resistance from the windings to ground using a DMM. I measured infinite resistance.
08-07-14, 07:57 PM
Replies: 11
Views: 12,292
Posted By Jeremy S

Carrier GE ECM Blower Motor Problem

I'm seeking some advice. I was asked to look at an 8 year old Carrier air handler, model FV4BNF003. The blower motor was not working.

The motor is a GE 2.3 ECM type motor. Upon pulling it apart I...
Showing results 1 to 12 of 12


 
Forum Jump