Search: Posts Made By: golfinator
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Replies: 11
Views: 19,225
Posted By golfinator

Thanks cheese. The clutch cable and throttle...

Thanks cheese. The clutch cable and throttle cables go thru a housing attached to the vertical handle bar by one bolt. I did adjust the clutch cable by sliding it in the housing and retightening the...
Replies: 11
Views: 19,225
Posted By golfinator

Thanks for hanging in there with me on this one.

Thanks for hanging in there with me on this one.
Replies: 11
Views: 19,225
Posted By golfinator

This must be an older Harmony II. It has a speed...

This must be an older Harmony II. It has a speed lever on the right side of the vertical support of the handle for speeds 1,2, and 3. This lever is held on by a 10mm bolt that goes thru a hole on the...
Replies: 11
Views: 19,225
Posted By golfinator

Thanks Cheese, I used lithium grease on the...

Thanks Cheese,
I used lithium grease on the parts. The shaft spring that supports the shaft key on each side was clean. Each wheel ratchets when moving forward, but locks up when it tries to...
Replies: 11
Views: 19,225
Posted By golfinator

Honda Harmony II HRT216TDA wheels won't reverse

This mower wouldn't roll backwards, forward was fine. It's a 3 speed and it lacked power on a steep hill. When it wouldn't roll backwards, I took off the wheels and gears, and the shaft would then...
Replies: 28
Views: 58,565
Posted By golfinator

Since the bearing was going to take a few days to...

Since the bearing was going to take a few days to get here (Atlanta), I decided to tear down to it. Found the belt was jammed up against the rear guide and one of the rear wheels broken. Reassembled...
Replies: 28
Views: 58,565
Posted By golfinator

Many thanks AAWrench. I'll order the bearing and...

Many thanks AAWrench. I'll order the bearing and go from there.
Replies: 28
Views: 58,565
Posted By golfinator

Toro Personal Pace Drive Problem

Model 20031 bought in '04. No problems until now. Mower barely moves forward and can't be pulled backwards. Can hear either an intermittent grinding noise or belt slipping noise. Was working fine 4...
05-03-08, 05:55 AM
Replies: 9
Views: 1,531
Posted By golfinator

Thanks Furd. This website, and the folks on it,...

Thanks Furd. This website, and the folks on it, have saved me time, money, and aggravation. Best to all.
05-02-08, 03:13 PM
Replies: 9
Views: 1,531
Posted By golfinator

Everything is working as you said it would, and...

Everything is working as you said it would, and many thanks for your help. For future reference, why was the receptacle that the TV was plugged into the only one on the circuit that was working(see...
05-02-08, 12:28 PM
Replies: 9
Views: 1,531
Posted By golfinator

Thanks to all of you helping me through this. ...

Thanks to all of you helping me through this.
So the next step is to take the two wires now connected to the load terminals and connect them to the line terminals? This will still leave me with a...
05-02-08, 06:03 AM
Replies: 9
Views: 1,531
Posted By golfinator

Thanks Marc, This is the only recept. in the...

Thanks Marc,
This is the only recept. in the bathrm. Haven't been able to map out the circuits as everything is enclosed in the walls. If there's a way to map with a meter, please let me know. Also,...
05-01-08, 01:15 PM
Replies: 9
Views: 1,531
Posted By golfinator

GFIC keeps tripping

2 Yrs. ago I tried to install a gfic in my bathroom because there was none. It kept tripping as soon as I installed it, so I reinstalled the old wall outlet thinking there was something wrong with...
Showing results 1 to 14 of 14


 
Forum Jump