Search: Posts Made By: feverdog71
Showing results 1 to 25 of 66
Search took 0.01 seconds.
Today, 06:18 AM
Replies: 7
Views: 106
Posted By feverdog71

The black wire from the ceiling is a good...

The black wire from the ceiling is a good circuit..........it had 120V on it and operated with the switch. So I could just forget about the other (red) circuit and wire both to the black and run it...
Yesterday, 12:55 PM
Replies: 7
Views: 106
Posted By feverdog71

https://cimg0.ibsrv.net/gimg/www.doityourselft.com...

https://cimg0.ibsrv.net/gimg/www.doityourselft.com-vbulletin/552x617/capture_9b28e5b06ded3c8a977698d2d996487ab699cfaf.jpg
Yes, two gang box with two switches.
Yes, black and red from the ceiling. ...
Yesterday, 10:43 AM
Replies: 7
Views: 106
Posted By feverdog71

Dual Circuit Ceiling Fan

The rooms in my house all have dual circuit ceiling fans. Not sure if that is correct terminology........one switch for fan, one switch for light.

The livingroom fan did not have a light on the...
Replies: 2
Views: 475
Posted By feverdog71

How to Splice Rectangular Duct

So, whoever installed my previous range microwave ran a rigid duct all the way on top of the old microwave without a damper. Not only that, but they didn't even have the blower facing up.
So, I"m...
Replies: 7
Views: 451
Posted By feverdog71

Good tip. The "Cover Stain" product says you...

Good tip. The "Cover Stain" product says you don't need to sand. Do you sand when you do stained cabinets?
Replies: 7
Views: 451
Posted By feverdog71

Painting over stained cabinets

I'm just getting started on this project. I used a deglosser and did some light sanding with 220 grit paper. But the problem is it took at least 5 or 6 coats of white for the dark stain not to show...
12-31-19, 12:11 PM
Replies: 11
Views: 592
Posted By feverdog71

Does anyone have any advice?

Does anyone have any advice?
12-27-19, 11:07 AM
Replies: 11
Views: 592
Posted By feverdog71

Yes, all 4 spark, but for some reason I'm not...

Yes, all 4 spark, but for some reason I'm not getting a strong spark at the one burner with it bolted up. The spark jumps to the side.....not the top.

If I take the stove top off, and set the...
12-27-19, 09:46 AM
Replies: 11
Views: 592
Posted By feverdog71

Update, My only problem left is the burner...

Update,

My only problem left is the burner that I broke the bolts on won't light. I have it bolted in straight now, but I'm not getting a strong spark.

If I take the stove top tray off and put...
12-26-19, 11:27 AM
Replies: 11
Views: 592
Posted By feverdog71

Well, finally took the time to do this today. But...

Well, finally took the time to do this today. But still have problems.

1. The burner I replaced still isn't sparking when I turn that burner on. If I turn another burner on, it will spark and...
12-15-19, 12:31 PM
Replies: 20
Views: 555
Posted By feverdog71

Laundry day. Bypassed the thermostat and...

Laundry day.

Bypassed the thermostat and made it up to 167 in about 50 minutes. I wanted to see when the high limit would kick it off, but heard a strange noise and turned if off.

Clothes...
12-14-19, 09:26 AM
Replies: 11
Views: 592
Posted By feverdog71

Now that the cold is here I'm back to indoor...

Now that the cold is here I'm back to indoor projects..........left this one alone for awhile.

Can anyone give me some advice? I am replacing a burner, but on my stove I need to unbolt each...
12-08-19, 02:19 PM
Replies: 20
Views: 555
Posted By feverdog71

Ok, so doing another load of laundry today. ...

Ok, so doing another load of laundry today.

The burner stayed lit for the entire first 30 minutes and got up to 145 degrees.
After the temp got down to about 115, the burner reignited.

Is that...
12-01-19, 04:29 PM
Replies: 20
Views: 555
Posted By feverdog71

I wasn't going to lay on the floor looking thru...

I wasn't going to lay on the floor looking thru the inspection hole the entire time, but I looked several times and the burner was on each time. And the temp never went above 92 with the burner lit. ...
12-01-19, 10:35 AM
Replies: 20
Views: 555
Posted By feverdog71

Well, a paltry 92 degrees was all I could get out...

Well, a paltry 92 degrees was all I could get out of it. Started on Medium heat and changed it to High and maybe got an extra 2 degrees. The burner was on every time I looked.

So this would...
11-30-19, 05:37 PM
Replies: 20
Views: 555
Posted By feverdog71

Model # - CRGR5700AS2 I went back and found...

Model # - CRGR5700AS2

I went back and found a big ball of lint in the front cover ductwork. So I decided to button it up and run a load (after replacing the belt that I'm sure I burned while...
11-30-19, 09:02 AM
Replies: 20
Views: 555
Posted By feverdog71

Now I'm totally confused. 1. The vent has...

Now I'm totally confused.

1. The vent has been off the entire time, so venting should not be an issue.
2. I bypassed the high limit, yet the burner still kicked off at about 2 minutes and never...
11-29-19, 06:37 PM
Replies: 20
Views: 555
Posted By feverdog71

So I put a voltmeter on the back side of the...

So I put a voltmeter on the back side of the thermostat and the burner was on for 4 minutes and then cut off, but the thermostat still had 19 volts on it, so that did not switch it off. The switch...
11-28-19, 01:47 PM
Replies: 20
Views: 555
Posted By feverdog71

My exhaust vent was completely clean so it has to...

My exhaust vent was completely clean so it has to be thermal control.

I just ran it on high heat. It was on for about 3-1/2 - 4 minutes. Off for about 2-1/2 minutes.

Not sure how long the...
11-28-19, 07:21 AM
Replies: 20
Views: 555
Posted By feverdog71

Long Drying Time

I have a Frigidaire Crown dryer with an LP kit. Lately I have to keep extending drying time to get the clothes dry. (The washer spin cycle is fine.)
I can hear the burner lighting. Would this be...
11-05-19, 06:14 AM
Replies: 3
Views: 221
Posted By feverdog71

My house is up for sale and I'm replacing the...

My house is up for sale and I'm replacing the glass to save that from being a bargaining chip. It looks like I'm not going to get what I want from the market, so I didn't want to pay double for the...
11-05-19, 05:48 AM
Replies: 3
Views: 221
Posted By feverdog71

Window Replacement Leaks?

I'm in the middle of replacing the window panes in my picture window. The old dual pane glass has fogged up. I'm replacing with 1/4" single pane.

All of the panes that I have been replaced so...
11-04-19, 09:46 AM
Replies: 2
Views: 259
Posted By feverdog71

Cold Exhaust Fan Ductwork

My fan duct radiates a very noticeable amount of cold air from the attic. Can I build a wood box around this to seal it off or does that violate some kind of code?
Replies: 3
Views: 165
Posted By feverdog71

Ok, so I ohm checked the compressor circuits and...

Ok, so I ohm checked the compressor circuits and got approx. 10, 6 & 4. So that should be good. I checked resistance on the capacitor. Its starts relatively low and keeps climbing up into the Mega...
Replies: 3
Views: 165
Posted By feverdog71

Yes, condenser is clean. Fan is running. I...

Yes, condenser is clean. Fan is running. I unplugged for over an hour and it just does the same thing.

Is that a breaker on the start device?

I opened up the back and pulled that unit off...
Showing results 1 to 25 of 66
 


 
Forum Jump