Search: Posts Made By: dcsbass
Showing results 1 to 25 of 27
Search took 0.01 seconds.
Forum: Water Heaters
02-05-09, 10:24 AM
Replies: 4
Views: 976
Posted By dcsbass

Talking How to check elements?

My (wife says) hot water tank not as hot. I want to check elements. What is best way ? Ohm or what? Also a good and easy way to check T stats? I'm going to check dip tube.
:wall:
Thank You David...
Replies: 6
Views: 1,849
Posted By dcsbass

carguyinva you are correct! I would look at Iac...

carguyinva you are correct! I would look at Iac and vacum leaks. Check codes, go from there.
:wall: :confused:
Replies: 2
Views: 965
Posted By dcsbass

It has a relay in front engine compartment. It is...

It has a relay in front engine compartment. It is marked on the cover. Check here! They can and will go bad.
:wall: :confused:
Replies: 3
Views: 2,387
Posted By dcsbass

By not running "Compressor". You may have a bad...

By not running "Compressor". You may have a bad relay or pressure switch. But "ODDS" are freon.You have a leak some where! You need to find it, repair or replace. Mine is over 8 years old. and still...
Replies: 3
Views: 1,613
Posted By dcsbass

I think you are saying that the switch,will work...

I think you are saying that the switch,will work when you put it passanger side correct? In and Out correct? Then when you try to adjust up and down it does both mirrors?
This I would look for a...
Replies: 1
Views: 739
Posted By dcsbass

It could be a couple of things. Bad switch or bad...

It could be a couple of things. Bad switch or bad starter solenoid, or bad trans switch. The click you hear could be starter solenoid,or could be fuel pump relay. It should be a gear reduction...
Replies: 15
Views: 4,155
Posted By dcsbass

They should be in steering knuckle. Most are...

They should be in steering knuckle. Most are pressed in. I can not say for sure if they have a lock ring on back side.
You can do it your self,just depends on you.
:wall: :confused:
Replies: 2
Views: 759
Posted By dcsbass

I'm sure they are different now. How they are...

I'm sure they are different now. How they are made but, I never replaced one with out a reason. Like oil on it, or antifreeze from blown head gasket. They will go bad. I can say for my self that I...
Replies: 3
Views: 1,595
Posted By dcsbass

Unclediezel is correct on the bolts and latches!...

Unclediezel is correct on the bolts and latches! Just climb under for both rear plugs. A whole lot easier. I use to change them all the time. You can get the others from wheel wells.There are rubber...
Replies: 5
Views: 2,512
Posted By dcsbass

Check Grounds, to motor. You should also check...

Check Grounds, to motor. You should also check out the air temp sensor! Coolant temp sensor! Something is telling ECM, that it's not up to temp. O2 can also be a problem! Stay rich or stay lean.You...
Replies: 1
Views: 1,920
Posted By dcsbass

Dash lights

All of the dash lights, in cluster? Check to make sure you haven't turned them off or all the way down.

:wall: :confused:
Replies: 3
Views: 18,466
Posted By dcsbass

windows

I will say it is most likely the switchs. You need to check to see if current is going out, when you push for front windows!
You could pull door panels and see if you have current at motor. I don't...
Replies: 5
Views: 4,762
Posted By dcsbass

I'm sure one (little one) goes first! But either...

I'm sure one (little one) goes first! But either the second one goes on top or it goes into a side port. I did get a name and number from the maker ,on who to call. The said this person designed it....
Replies: 6
Views: 1,416
Posted By dcsbass

I know it's in a manual. But I would just take it...

I know it's in a manual. But I would just take it in and get it realigned. Let them do it.

:wall: :confused:
Replies: 13
Views: 5,181
Posted By dcsbass

Or Belt. If it is worn out. Check that also. ...

Or Belt. If it is worn out. Check that also.

:wall: :confused:
Replies: 4
Views: 3,294
Posted By dcsbass

It could be a couple of things. Try to pin point...

It could be a couple of things. Try to pin point were it is comeing from. Is overflow boiling out or draining? Are your hose clamps tight? Could have a leak in bottom radiator hose? Sounds like...
Replies: 5
Views: 4,762
Posted By dcsbass

No one knows where, a person can get a diagram of...

No one knows where, a person can get a diagram of a floor jack pump?I know how it works ! Only problem I have is two check valves.
David C

:wall: :confused:
Replies: 21
Views: 2,568
Posted By dcsbass

Check under hood and see if there is a bare wire...

Check under hood and see if there is a bare wire around headlights and turn signals. This is a different circut than brake lights.Good Luck!
David C

:wall: :confused:
Replies: 7
Views: 952
Posted By dcsbass

If it ran worse after you put it in gear! It's a...

If it ran worse after you put it in gear! It's a plug or wires. Check PVC also fuel filter, part of a good tune up.
Good Luck!
David C

:wall: :confused:
Replies: 26
Views: 1,824
Posted By dcsbass

I do the same splice kit that carguyinva does....

I do the same splice kit that carguyinva does. That is the only kit I have ever used. Good Luck!
David C

:wall: :confused:
Replies: 5
Views: 804
Posted By dcsbass

Like 94 Jimmy said a ground is a good start. Also...

Like 94 Jimmy said a ground is a good start. Also a manual. I would check coolant temp. sensor. If running better cold than hot. Also check alternator out put. If off will cause a problem.
Hope this...
Replies: 4
Views: 934
Posted By dcsbass

I hope you bleed the brakes. Does this have anti...

I hope you bleed the brakes. Does this have anti lock Brakes? I think it should! Let me know and we'll go from there. David C

:wall: :confused:
Replies: 21
Views: 2,568
Posted By dcsbass

Did this car set for awhile, before you started...

Did this car set for awhile, before you started useing it again?
If so look for wires that a mouse or varmint could chew on.
You have a direct short.Start checking from where you unpluged forward....
Replies: 26
Views: 1,824
Posted By dcsbass

brakes

They also make a splice kit for this tubeing. If rusty replace it from front to rear. If not you "can" put a splice kit in. Like Marksr said it's not real hard. Make sure when you fix line you bleed...
Replies: 7
Views: 952
Posted By dcsbass

4.3 runs bad

It could also be a bad spark plug. Bad spark plug wire. Bad lifter. Bad Gas! Several things. Water under cap or bad cap.
Even a bad vacum leak can cause a big Problem. I think if memory is...
Showing results 1 to 25 of 27
 


 
Forum Jump