Search: Posts Made By: nfored
Showing results 1 to 11 of 11
Search took 0.01 seconds.
10-21-16, 06:52 PM
Replies: 2
Views: 777
Posted By nfored

Thank you, I have went back over the solder. I...

Thank you, I have went back over the solder. I didn't know that about the fuses I thought it was total heat that caused them to blow. So I thought someone smarter than I am figured out 125v@xA...
10-21-16, 05:22 PM
Replies: 2
Views: 777
Posted By nfored

Okay Way to install Fuse Holder.

I bought some Solder on Fuse holders, and modified them to fit one end into to my terminal box.

I basically clipped of a section of the slot where you solder the wire so I could fit the screw...
10-17-16, 10:33 PM
Replies: 6
Views: 865
Posted By nfored

Thank you for the advice order placed, the hot is...

Thank you for the advice order placed, the hot is covered with plastic cover, just hard to see though in my photo. I will move the ground probes to the enclosure for sure no one would mistakenly...
10-17-16, 10:10 PM
Replies: 6
Views: 865
Posted By nfored

Sorry to post so much. Can you recommend a good...

Sorry to post so much. Can you recommend a good fuse holder? All the ones I see on amazon for 5x20 or 1/4 are only rated at 15amps 125v. I was planning on using the gma-6 amp fuse, and I saw some...
10-17-16, 09:24 PM
Replies: 6
Views: 865
Posted By nfored

I agree short between hot and neutral won't trip...

I agree short between hot and neutral won't trip gfci.
I was going to fuse each relay, but was not sure if it really bought any safety. My thinking was if it was not me making this but just...
10-17-16, 06:11 PM
Replies: 6
Views: 865
Posted By nfored

Forgot. My Understanding of how the GFCI...

Forgot.

My Understanding of how the GFCI works is it uses a CT on Hot and Neutral, and expects they are equal. So I am expecting that if in the tank/filter if there is a failure the ground probe...
10-17-16, 06:06 PM
Replies: 6
Views: 865
Posted By nfored

Looking for safety double check for project

Hello All.

Working on my first High Voltage arduino project, I have tried to build the whole thing with safety in mind. Hoping for double check of anything you think I might have not thought of or...
09-12-16, 03:06 PM
Replies: 5
Views: 518
Posted By nfored

So I looked at some data sheets and think you...

So I looked at some data sheets and think you guys are on to something. Using a 6amp fuse gives me around 10-30 seconds to interrupts at 10.3amps, and the Watters heater I am going to controlled is...
09-12-16, 09:27 AM
Replies: 5
Views: 518
Posted By nfored

Thank you very much. Its good to hear some feed...

Thank you very much. Its good to hear some feed back on the relay as well. I was hopeful that they would just fail open and not catch fire :-). Not sure my wife would appreciate me burning down the...
09-12-16, 09:01 AM
Replies: 5
Views: 518
Posted By nfored

Bussman 125v Fast Blow Fuses

Hello All.
I am am building outlet that I can control with and arduino. The load only cause for 5 amps, and the arduino relay is rated at 10 amps.

Safety first I have been looking to put a...
08-01-13, 08:21 PM
Replies: 1
Views: 754
Posted By nfored

Range Breaker.

Hello all.
I decided today I was going to move the range for my wife to make better use of the small living room. I went down stairs to check out how hard it would be to run the 6/3 wire; I...
Showing results 1 to 11 of 11


 
Forum Jump