Search: Posts Made By: agfreesafety
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Replies: 23
Views: 4,273
Posted By agfreesafety

Baffled.

A few weeks ago, I started and restarted the machine numerous times while holding the probes against the two terminals for long periods of time, and I never got a reading for voltage.

I even...
Replies: 23
Views: 4,273
Posted By agfreesafety

...so are you saying that I need to make sure I'm...

...so are you saying that I need to make sure I'm testing the voltage on the input valve at the very beginning of the cycle, since that valve is only sent power during the first 60 seconds of the...
Replies: 23
Views: 4,273
Posted By agfreesafety

I turned the power on to the dishwasher, set it...

I turned the power on to the dishwasher, set it to start (where the water comes-in initially) set the meter to the 300VAC scale and placed the leads here:

41125

...and the meter didn't move. ...
Replies: 23
Views: 4,273
Posted By agfreesafety

OK, so now I need to go back and re-check the...

OK, so now I need to go back and re-check the inlet valve for voltage? Just making sure I understand what you're saying, being that I already checked it earlier for resistance.

If so, do I check...
Replies: 23
Views: 4,273
Posted By agfreesafety

It Was Working for a While...

The dishwasher started working for about 2-3 loads after I cleaned the float, and checked the resistance at the intake valve and float as you guys recommended.

I kinda wonder if there's a short...
Replies: 23
Views: 4,273
Posted By agfreesafety

Yep, that's what happened. What should I...

Yep, that's what happened. What should I look-into next? I cleaned-up most of that gunk that was showing on the float in the picture I posted earlier, by the way...
Replies: 23
Views: 4,273
Posted By agfreesafety

When you say that it should show a "dead short,"...

When you say that it should show a "dead short," are you saying that nothing should happen on the meter (the meter doesn't move, in other words) when I test the two lines? I ask, because that's...
Replies: 23
Views: 4,273
Posted By agfreesafety

So this is what I'm looking at after I removed...

So this is what I'm looking at after I removed the top from the float.

40731
Not sure why I bothered taking it off, after re-reading your instructions, it appears that it wasn't necessary,...
Replies: 23
Views: 4,273
Posted By agfreesafety

I finally got the plug disconnected from the...

I finally got the plug disconnected from the valve; I'm getting the same reading on the meter as I did before.

It's moving slightly, but the reading isn't making it to the range referenced in the...
Replies: 23
Views: 4,273
Posted By agfreesafety

Oh, and the water is indeed flowing to the...

Oh, and the water is indeed flowing to the dishwasher
Replies: 23
Views: 4,273
Posted By agfreesafety

When I try to disconnect the wire harness from...

When I try to disconnect the wire harness from the terminals on the inlet valve it won't come completely off. I stopped pulling out of fear of damaging something. I was pulling extremely hard, but...
Replies: 23
Views: 4,273
Posted By agfreesafety

GE Nautilus Dishwasher - No Water Coming In

I have a GE Nautilus Model number GSD2200F00WH.

When I turn it on and let it run for a few minutes, I open it up and discover that absolutely no water has entered the dishwasher.

I've done...
Showing results 1 to 12 of 12


 
Forum Jump